The wishlist name can't be left blank
Single transmodulator equipped with remultiplexing DVBS/S2 - DVBC (QAM Annex A) equipped with CI

Single transmodulator equipped with remultiplexing DVBS/S2 - DVBC (QAM Annex A) equipped with CI

Twin Transmodulator equipped with remultiplexing DVBS/S2 – DVBT (COFDM) or DVBC (QAM), with CI

Transmodulator generating two COFDM or QAM (Annex A) multiplex from the multiplexing of the services available in up to 4 different TV SAT transponders. These may be extracted from 2 different satellite polarities (2 independent SAT inputs), or from a single satellite polarity, using the headend's input loop.

The encrypted satellite channels are transformed into free terrestrial services through the CI interface and the appropriate CAM module. Depending on the CAM type used (standard/professional), one or several services may be opened for free visualization.

The selection of the desired output modulation can be possible via an embedded web user interface, which allows the configuration of the module.

Download our brochure and discover all its advantages
Ref. 565401
Product Sheet
EAN13: 8424450273708
SKU
565401
Highlights
  • Embedded user web interface for module configuration:
    • Selection of output modulation COFDM (DVB-T) or QAM (DVB-C)
    • Configuration of the entire headend selecting one of the module as a master
    • Automatic detection of the modules that are connected to the master
    • Cloning function to replicate configurations between modules and headends
    • Headend control indicators: module temperature, CAM status ...
  • Access to the headend configuration through a self-created WiFi network (using the kit with ref.216802)
  • Total or selective removal of the services present in the received transponder, to avoid them being detected (and memorized) by the receivers (STB)
  • Editable TS_ID, which makes programme/service detection easier on the receiver (STB), since the channel scan is based on this identifier
  • LCN (Logical Channel Number) allows the assignment of the services present in the output to an LCN, which makes the ordering of the channels easier on the receivers (STB)
  • Provides information regarding both the occupation of each specific service and the global output occupation, which allows the optimization of the services being distributed
  • Device monitoring and signal status LEDs

Main features
  • Its outputs can be configured with loop mode either activate or deactivate
  • Service decryption by insertion of a PCMCIA module
  • Null packet insertion (“Stuffing”) allows the receiver (STB) to perform a faster scan
  • PID filtering allows the removal of undesired services from a Multiplex (enhanced occupation use); very interesting when combined with CAM use
  • S_ID editable to prevent the receivers (STB) in an installation from retuning when the output-Multiplex's services are modified
  • Editable Network_ID, Original Network_ID and Cell_ID allow the control of network identifiers

SAT INPUTS Input frequency MHz 270...2320
Symbol rate Mbaud 2 - 42,5 (Max 140 Mbps netto bitrate)
Frequency steps MHz 1
Input level dBm -60 ... -25
Input/Output connectors "F"-female
Input impedance Ω 75
LNB powering V/KHz 13V/17V/ OFF - 22KHz (ON/OFF)
dCSS MSW control SCR II (EN50494/EN50607/SKY UK)
Satellite selection (DiSEqC) A,B,C,D
Through losses dB ≤ 1,5 typ (2 max)
Modulation DVB-S2X QPSK, 8PSK, 8/16/32 APSK (EN 302307-2)
DVB-S2 QPSK, 8PSK (EN302307)
DVB-S QPSK (EN300421)
FEC inner code LDPC 9/10, 8/9, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2
FEC outer code Bose-Chaudhuri-Hocquenghem
Roll-Off factor % 20,25,35
R.O.E. inner dB 10 typ (8 min)
QAM MODULATOR Modulation format QAM 16,32,64,128,256
Symbol rate Mbaud 2 - 7,5 (select.)
Roll-Off factor % 15
Block code Reed Solomon (188,204)
Scrambling DVB ET300429
Interleaving DVB ET300429
Bandwidth (max.) MHz 8,3
Spectral inversion (select.) Normal/Inverted
COFDM MODULATOR Modulation format QPSK,16QAM,64QAM
Guard interval 1/4, 1/8, 1/16, 1/32
FEC 1/2, 2/3, 3/4, 5/6, 7/8
Bandwidth MHz 6,7,8
Scrambling DVB ET300744
Interleaving DVB ET300744
Cell_id Seleccionable
Spectral inversion (select.) Normal/Inverted
RF OUTPUT Output frequency MHz 46...862
Frequency steps KHz 1
Max. output level (select.) dBμV 85±5
Attenuation (select.) dB >15
Through losses (typ.) dB ≤ 1,5
Return losses (typ.) dB > 10
Input/Output connectors "F"-female
Ouptut impedance Ω 75
GENERAL Control interfaces Ethernet 10/100/1000
USB 2.0
Consumptions (@24V) Base mA 700
+ CAM + 100
+ LNB + 250/LNB
Max. 1300
Max. operating temperature ºC 45
Protection index IP 20

Physical data

Net weight: 1,074 g

Gross weight: 1,210 g

Width: 50 mm

Height: 217 mm

Depth: 175 mm

Main product weight: 990 g

Packing

Box 1 Units

More Information
tlv_reflog U4Q2CQA-S2-CI
tlv_tabla_especificaciones
SAT INPUTS Input frequency MHz 270...2320
Symbol rate Mbaud 2 - 42,5 (Max 140 Mbps netto bitrate)
Frequency steps MHz 1
Input level dBm -60 ... -25
Input/Output connectors "F"-female
Input impedance Ω 75
LNB powering V/KHz 13V/17V/ OFF - 22KHz (ON/OFF)
dCSS MSW control SCR II (EN50494/EN50607/SKY UK)
Satellite selection (DiSEqC) A,B,C,D
Through losses dB ≤ 1,5 typ (2 max)
Modulation DVB-S2X QPSK, 8PSK, 8/16/32 APSK (EN 302307-2)
DVB-S2 QPSK, 8PSK (EN302307)
DVB-S QPSK (EN300421)
FEC inner code LDPC 9/10, 8/9, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2
FEC outer code Bose-Chaudhuri-Hocquenghem
Roll-Off factor % 20,25,35
R.O.E. inner dB 10 typ (8 min)
QAM MODULATOR Modulation format QAM 16,32,64,128,256
Symbol rate Mbaud 2 - 7,5 (select.)
Roll-Off factor % 15
Block code Reed Solomon (188,204)
Scrambling DVB ET300429
Interleaving DVB ET300429
Bandwidth (max.) MHz 8,3
Spectral inversion (select.) Normal/Inverted
COFDM MODULATOR Modulation format QPSK,16QAM,64QAM
Guard interval 1/4, 1/8, 1/16, 1/32
FEC 1/2, 2/3, 3/4, 5/6, 7/8
Bandwidth MHz 6,7,8
Scrambling DVB ET300744
Interleaving DVB ET300744
Cell_id Seleccionable
Spectral inversion (select.) Normal/Inverted
RF OUTPUT Output frequency MHz 46...862
Frequency steps KHz 1
Max. output level (select.) dBμV 85±5
Attenuation (select.) dB >15
Through losses (typ.) dB ≤ 1,5
Return losses (typ.) dB > 10
Input/Output connectors "F"-female
Ouptut impedance Ω 75
GENERAL Control interfaces Ethernet 10/100/1000
USB 2.0
Consumptions (@24V) Base mA 700
+ CAM + 100
+ LNB + 250/LNB
Max. 1300
Max. operating temperature ºC 45
Protection index IP 20
tlv_ean 8424450273708
tlv_dim_product_x 50
tlv_dim_product_x_label Width
tlv_dim_product_x_unit mm
tlv_dim_product_y 217
tlv_dim_product_y_label Height
tlv_dim_product_y_unit mm
tlv_dim_product_z 175
tlv_dim_product_z_label Depth
tlv_dim_product_z_unit mm
tlv_weight_product_label Main product weight
tlv_weight_product 990
tlv_weight_product_unit g
tlv_gross_weight_label Gross weight
tlv_gross_weight 1,210
tlv_gross_weight_unit g
tlv_net_weight_label Net weight
tlv_net_weight_unit g
tlv_net_weight 1,074
tlv_1_type_pack Box
tlv_1_type_pcs_pack Units
tlv_1_pcs_pack 1

Remultiplexing of services

The unit has four demodulators (TS A, TS B, TS C, TS D) that, depending on how the loop mode is configured, one or two bands and polarities should be available for all demodulators.

The inputs can also be configured to receive signals from a dCSS multiswitch of up to 4 different satellites in a single cable.

Configuration of the tererstrial signals at the outputs

It is possible to select the standard between DVB-T or DVB-C, which is applied to the two outputs of the module. In addition, the desired services can be selected, individually or multiple, for each output as well as in which RF channel these services will be included.

Programming of the entire headend selecting one of the module as a master

Configure one of the modules as a master of the entire headend. Any module can be selected as the master. Once the master mode is activated, the unit searches for other units connected to the network (ETH2).

The units can be visually ordered in the web interface to identify them more easily with the real position in the headend. Each of the modules can be identified by temporarily activating the flash of the front LED.

Separated networks in each module

Each unit has two Ethernet RJ45 connectors, which can be used on an single network or on two separate networks. Users can be enable the separation of these networks (Split Net Ports) and configure the IP address, subnet mask, and default port link, as well as the DHCP client mode.

Cloning of headends configurations

The web interface allows to export/import files for duplicating units (or complete headends) configurations. This function helps to reduce time in typical installations, due of having previously a configured file. The exportation of these files also allows to have a headend configuration backup.

Status reports generation

Users can download report files on the selected unit, or of the complete headend, to make easier debugging in the event of an incident.

Mounting details

HEADEND CONFIGURATION WITH ETHERNET CABLE

The unit’s IP must be known to access its control web interface. By default, this code is printed on the rear label.

  1. Connect a PC directly to the module’s ETH1 port with an Ehternet cable.
  2. Configure the PC’s IP address on the same subnetwork as the module.
  3. Open a browser and go to the URL https://ip_module

Mounting details

HEADEND CONFIGURATION WITH WIFI ADAPTER

The unit can also be connected via Wi-Fi using the adapter kit Ref. 216802. This adapter must be connected to the micro USB port on the front of the unit. After an automatic initialization process, connection to a Wi-Fi network will be possible, provided its SSID has the following format: Televes_mng_XXYYZZ. To go to the configuration website, open a browser and go to the URL "https://config.local".